Drawing of poly(p-phenylene sulfide) by solid-state coextrusion

The effects of drawing temperature on the physical and mechanical properties of poly(p-phenylene sulfide) have been studied. A melt-quenched film was drawn by solid-state coextrusion both below (75°C) and above (95 and 110°C) the glass transition temperature T_g (85°C) of PPS. The maximum extrusion draw ratio (EDR_max) increased from 3.4 to 5.6 with increasing extrusion temperature T_e from 75 to 110°C. It was found that extrusion drawing just above the T_g of PPS (95°C) produced more stress-induced crystals. A high efficiency of draw in the amorphous region was achieved by extrusion at T_e-75°C. The tensile modulus at EDR_max decreased from 5.1 to 3.5 GPa with increasing T_e from 75 to 110°C. The low efficiency of draw for the samples extruded at 110°C is explained in terms of disentanglement and chain slippage during drawing due to a less effective network.     

Chain orientation in polystyrene/poly(2,6-dimethyl-1,4-phenylene oxide) blends

The differential orientation of polymer chains has been measured in polystyrene (PS)/poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) compatible blends. Density measurements are reported as a function of binary blend composition at 23°C. Drawing was performed by solid-state coextrusion. PS/PPO blend compositions of 90/10 and 75/25 were drawn within sandwiches of polyethylene at 145°C and isotactic polypropylene at 155°C, i.e. at ca. 25°C above the glass transition temperatures of the two blends. The change in Fourier-transform infrared dichroisms on drawing these blends was measured at 906 and 1190 cm^?1, corresponding to predominantly PS and PPO, respectively. The orientation of PS and PPO was observed as a function of draw ratio λ in the range 1–5; orientations increased with λ for both PS and PPO in both blends but to different degrees. Both polymers decreased in orientation with increasing PPO content. Annealing with fixed ends showed that the PPO chains disorient more slowly than those of PS. All binary systems were found to be amorphous and compatible.     

An electron transfer model for PGI biosynthesis

A biomimetic conversion of the endoperoxide 1b to prostacyclin (PGI₂) analogs is achieved with the aid of ferrous ion catalysis.     

Electrochemically modulated liquid chromatographic separations of inorganic anions

Inorganic anion retention on a porous graphitic carbon (PGC) stationary phase is investigated by electrochemically modulated liquid chromatography (EMLC). Through various combinations of the potential applied (Eapp) to the PGC packing and/or changes in the composition (sodium salts of tetrafluoroborate, sulfate, and fluoride) and concentration (10, 25, and 50 mM) of an aqueous mobile phase, conditions for the separation of two different inorganic anion mixtures (iodate, bromide, nitrite, and nitrate or iodate, bromate, and chlorate) are developed. Results show that retention was affected by both variables, with the analyte retention factor, k', changing in a few cases by as much as a factor of ca. six. Moreover, plots of In k' are linearly dependent on both Eapp and In [SE], where [SE] is the supporting electrolyte concentration. Based on these findings, insights into the retention mechanism are briefly discussed by drawing on the theory for ion exchange chromatography.     

Effect of polymer surface activity on cavitation nuclei stability against dissolution

The persistence of acoustic cavitation in a pulsed wave ultrasound regime depends upon the ability of cavitation nuclei, i.e., bubbles, to survive the off time between pulses. Due to the dependence of bubble dissolution on surface tension, surface-active agents may affect the stability of bubbles against dissolution. In this study, measurements of bubble dissolution rates in solutions of the surface-active polymer poly(propyl acrylic acid) (PPAA) were conducted to test this premise. The surface activity of PPAA varies with solution pH and concentration of dissolved polymer molecules. The surface tension of PPAA solutions (55-72 dynes/cm) that associated with the polymer surface activity was measured using the Wilhelmy plate technique. Samples of these polymer solutions then were exposed to 1.1 MHz high intensity focused ultrasound, and the dissolution of bubbles created by inertial cavitation was monitored using an active cavitation detection scheme. Analysis of the pulse echo data demonstrated that bubble dissolution time was inversely proportional to the surface tension of the solution. Finally, comparison of the experimental results with dissolution times computed from the Epstein-Plesset equation suggests that the radii of residual bubbles from inertial cavitation increase as the surface tension decreases.     

Role of hyperconjugation in determining carbon-oxygen bond dissociation enthalpies in alkylperoxyl radicals

[reaction: see text] Theoretical calculations of carbon-oxygen bond dissociation enthalpies in substituted methylperoxyl radicals (YCH(2)OO*) reveal that bond strengths are not governed solely by the stability of YCH2* radicals but are largely affected by hyperconjugation when Y is electron-donating or conjugating. In many cases, this hyperconjugative effect is greater than stabilization of the methyl radical by Y. All electron-withdrawing Y exert small destabilizing effects via inductive withdrawal of electrons from the polarized C-OO* bond.